Saprankov
Diaz

Installing manual

   Home    >    VW - Passat B5, Golf , Bora, Jetta IV, Skoda - Octavia, Fabia, Superb, Seat - Leon Cupra R Toledo

3DColorMFD ver. 7.5

VW 
Passat B5+ 

(B5.5; 3bg; Fl)


Golf 4

Bora/Jetta IV

(4.5 (Brasil)

Skoda
Octavia MK1
Fabia MK1
Superb MK1

Seat
Leon
Cupra R
Toledo

You will need:

Soldering iron 40 W

Tin

Flux

Multimetr

Tweezers
Nippers Pliers Knife Thermocouples And screwdriver Torx T10

Safety precautions

DO NOT!

ATTENTION!!! When installing a color MFD, there are 3 most important points.


1. You need to configure the power supply to 5.5v.

The MFD operates at a voltage of 5.5v. When you connect the power supply to the MFD

you should make sure that the output of the contacts is 5.5v, otherwise it will damage the processor! Paragraph 18


2. It is necessary to cut the power paths going to the pins 23 24 25,

then check that they are not voltage-free, you need to supply power to the cluster

and check with a tester, one probe into the ground of the second to each pin 23 24 25. Should be 0v . Paragraph 10


3. You need to rinse all the soldering points. Install very carefully.

After soldering the wires, it is essential to rinse the soldering points with special flushing agents

or isopropyl alcohol. During washing, do not allow alcohol to enter the display or under the display and its board!

 

1. Disassemble the cluster. 

With a screwdriver torx T10, unscrew the two screws edges on the rear of the instrument panel.

 

Bend all the latches neatly remove the front of the case with glass

View from above

Bottom view

1.   Remove the arrows (scroll counter-clockwise and simultaneously pull ourselves).

Either Using knives for oil or spatula, shoot the arrows from their shafts. It is necessary to put

A cardboard or napkins between the nomes and the base of the device to avoid damaging it. Necessary

Pull the arrows up to yourself.

2.                 Then remove the substrate.

3.                 Cut the jumpers, we work carefully, so as not to damage the board.

It should look like this:

5. Remove the excess.
On clusters with fullFIS, a temperature sensor is installed, it can be removed with a soldering iron

or simply cut off the sensor tape in any convenient place so that it does not interfere later.

It is necessary to remove the display by gently heating the loop with which it is soldered to the board, do not tear off the display as you can damage the dashboard board.

6. With the help of pliers we bend the metal clamps restraining fullFIS display.

7. Remove the white diffuser. On the back of the board, are visible white plastic latches,

bend them with your fingers and take out the white plastic

The basis of the display.

8. We solder the plume of the standard display and remove it.

On some instrument panels, the plastic base of the OEM FIS is soldered to the board quite seriously,

to dismantle it is best to remove the tin from using a soldering iron and a special vacuum.

9. Then you need to remove all the LEDs that are were under the standard display

We make sure that there are no jumpers made of tin. 

After removing the LEDs, clean the board of the residues of tin and rinse with alcohol

10. VERY IMPORTANT:

For instruments with a halfFIS or fullFIS installed, it is necessary to find and cut
tracks from
the pins of the control of the standard FIS
on the board of the instrument panel (from the pins 23, 24, 25 of the green connector)
After need to check that the 23, 24, 25 pins were 0v

Below are photos from some instruments.
On your device, the tracks may be located elsewhere
For dash have noFIS, you just need to check that the 23, 24, 25 pins were 0v

Instrument panel from Octavia with BK in the screen under the tachometer.

10.             We start to build wires according to the table. Wires are cleaned of

Isolation and twisting, ludim and cut off excess.

12. Through the holes in the board of the device, we extend the wires to the blue

And green connectors.

13. Using the tester, we find the wires we need and solder them to the feet connector according to the table.

Full size image

     

 

It is necessary to twist the wires of the connection to the CAN-bus into a spiral.

 

1-st Option

Also, for ease of installation, it is possible to solder the wires either according to the diagram above or from the back of the instrument panel chamber.
2-nd Option

Lay the wires in such a way that they do not interfere with the installation of white

Light diffuser.   

14. On the cluster without FIS and with halfFIS it is necessary to solder the wire from the 32 pin of module slots to the oil LED on the board.
And on the instrument panel with a FullFIS, this wire does not need to be soldered!

The dashboard with noFIS looks like this:

The dashboard with halfFIS looks like this:

Resistors instead of light-emitting diodes, as on a photo, it is not necessary to solder, we leave an empty place.

Important!
If you have half FIS or no display at all
It is necessary to sting this resistor from the module board

15. Connect the USB cable as follows:

16.

If you are the lucky owner of Passat B5 released for the North American or USA market, you have to add a few SMD resistors to the board of the device.

 

Since Americans do not bother at all about the engine oil. In the cluster for the American market there are no resistors responsible for the level alarm and Oil temperature, and the opening of the hood.

 So it's not right!

Attention!

18. Before installing the power supply, you need to solder the wires to it contacts + IN - IN and + OUT - OUT , then apply a current of 12V to + IN - IN , and connect the + OUT - OUT wires to the tester.

Now we need to adjust the output current. Using a small flat screwdriver slowly rotate the special metal knob (figure 1 in the picture.) Clockwise

Arrow, until, at us on the tester will not appear 5,5v in an output voltage.

Next we place the power supply unit on the back side, we bring to its contacts the wires from the blue connector.

9-pin of the blue connector is connected to the e - IN on the power supply board.

23 the leg of the blue connector is connected to + IN On the power supply board,

Contact + OUT Connects to the module's 36 pin, - OUT Connects to 43 module pin

Choose the place of installation of the power supply so that during assembly it does not interfere. Here are the possible

Options:

Attention!

After wiring, lay it so that they do not interfere with further assembly. We call all contacts and check on the table to avoid confusion anywhere.

  

20. Cut off the main beam guide part.

On the red line.

Leave the semicircle.

  21. Bite off the protruding part!

22. Before installing the display, you need to glue two-way cattle into three layers on the back of the display to lock the display.
Attention, you do not need to attach modules to the board!
It is enough simply to remove an additional support from a double-sided adhesive tape without removing the protective layer from the side of the module board.

After you solder the wires and set the display to its place, you need to test the MFD's performance in the car to make sure everything is properly installed and working well.

23. We take double-sided adhesive tape on a foamy basis, cut the squares 1cm X 1cm.

24. We collect these squares in 3 floors.

25. And we place them so that we do not have anything to do with mounting the module on the board

   

26. Place the module so that it is placed in the window of the device

27. For greater reliability, when the module is already installed on the board, and you calibrated it in the window so that there were no distortions, it is better to fix it.

Its hot glue along the edges of the module.

Next, you need to glue the matte protective film so that the display does not glare in the sun.

Attention! Be sure to stick the film!
Otherwise, you may damage the display!

 

If you have a 1J0 comfort unit installed.
NECESSARY to stretch the wires from the comfort unit to the appliance
The comfort block 9 -> on the terminals of the 8th leg of the device (CAN-H Comfort) of the green connector.
The comfort block 6 -> on the terminals of the 9th leg of the device (CAN-L Comfort) of the green connector.

 

 

 

Installation of the IMMO3 cluster in a vehicle with IMMO2

When installing the IMMO 3 instrumentation together with the comfort unit 1J0 -It is necessary to remove 2 resistors

Going from 8 and 9 contacts of the green connector, and then connect from 3DColorMFD

To terminals 8 (CAN-H Comfort) and 9 (CAN-L Comfort) of the green connector.

If you Installating IMMO3 cluster in a vehicle with IMMO2

Setting the ambient temperature sensor

Need activate ambiant temp in diag

 

 Passat B5

You need to change 1ef from 08 to 01

line 0001E0 column F

  

Golf 4

Cluster 1J0920806G no fis no show temp in dispay

You need to change 1e5 from 2B to 2F

line 0001E0 column 5

 

Change 2B in 2F and work

I changed that one 1E0 column 6 from 2B to 2F and it works

In order to connect the boost pressure control.

You will need to add one PIN to the green dashboard connector on the 15th leg.

 

And the other end of the wire should be connected from the side of the motor brain

(EBCUD to a blue - gray wire (blue with a gray bar) to the incoming

On the 101st contact of a smaller brain connector.

On diesel engines (AVB and others): 
- 71st contact of the motor brain, green - red Wire (green with a red stripe).

On petrol (AWM and others): 
- 101st contact of the motor brain, gray - blue wire (gray with a blue stripe).

In general, as far as I understand, at all B5-x diesel 1.9T supercharging is connected to the 71st

And the gasoline 1.8T is connected to the 101st contact. The color of the wire can vary depending on the year / engine.

 

BES 2.7T T121 101 pin

blue-gray

  AJM 1.9TD T121 71 pin

yellow-black

AKN 2.5TD T121 71 pin

yellow-red

  AUY 1.9TD T121 71 pin

yellow-black

BQW 2.0TD T94 78 pin

green-red

  AWT 1.8T T121 101 pin

blue-gray

AVG 1.9TD T80 40 pin

yellow-green

  AWM 1.8T T121 101 pin

blue-gray

AFN 1.9TD T121 70 pin

green-red

  AWD 1.8T T121 101 pin

blue-gray

AVB 1.9TD T121 71 pin

green-red

  AWP 1.8T T121 101 pin

violet-gray

AVF 1.9TD T121 71 pin

green-red

  AUM 1.8T T121 101 pin

violet-gray

AWX 1.9TD T121 71 pin

green-red

  AUQ 1.8T T121 101 pin

violet-gray

AHF 1.9TD T121 71 pin

yellow-black

  ARZ 1.8T T121 101 pin

violet-gray

ALH 1.9TD T121 71 pin

yellow-black

  ARX 1.8T T121 101 pin

violet-gray

ARL 1.9TD T121 71 pin

yellow-black

  ANB 1.8T T121 101 pin

blue-gray

ASV 1.9TD T121 71 pin

yellow-black

  APU 1.8T T121 101 pin

blue-gray

ASZ 1.9TD T121 71 pin

yellow-black

  APB 1.8T T121 101 pin

blue-gray

ATD 1.9TD T121 71 pin

yellow-black

  AMB 1.8T T121 101 pin

blue-gray

AXR 1.9TD T121 71 pin

yellow-black

           

And then we collect everything in the reverse order without forgetting to calibrate the needles with the help of the WAG-com.

I.       To do this, connect the device to the machine without installing the glass, connect the VAG-com,

 

Ii.       Go into the 17-unit dash panel

Iii.       Select test performers.

Iv.       Choosing in turn a tachometer, temperature and the rest, the arrows in turn will be

Do a turn on the whole scale, and then freeze on:

1.      Tachometer - 3 thousand revolutions

2.      Pace. Coolant - middle

3.      Fuel level - middle

4.      Speedometer - at 100 km / h

V.       Then turn off the power from the device!

Vi.       And set the arrows correctly rotating them in the desired direction.

Vii.       Then check everything again

Viii.       You can not turn the needles too quickly correcting the position, you can to damage the motors of the needles

Ix.       You can not turn the arrows when there is power on the device.